Grooved Pins

Grooved pins are non-threaded press fit fasteners a fastener that is pressed into an appropriate sized hole, providing the proper interference fit to lock the fastener in place. It is Commonly used as locking devices, pivots, bearing faces or locating elements where there is not a high degree of end load.It is available with many different groove types.

Typically zinc-plated, made from unhardened, low-carbon steel but available in a wide range of finishes and heat treatments for shear resistance.The groove of a grooved pin is formed by a swaging operation in which three tools penetrate the nominal diameter of the metal at 120 intervals. This penetration displaces a controlled amount of metal to each side of the grooving tool, forming a raised portion along the side of each groove.


Full Length Grooved Pin (with pilot end)

DIN: 1470 Grooved Pins are parallel pins with three equi-spaced longitudinal grooves.
IS : 7384 Pressed into the cylindrical body to deform the pin stock outward.
EN: 28 739 Only straight Drilled hole required. No reaming needed.
  Full Length Grooved Pins (with pilot end) are manufactured as per DIN: 1470, IS : 7384, EN: 28 739, ISO: 8739

Full Length Grooved Pin (with chamber end)

DIN: 1473 Grooved Pins are parallel pins with three equi-spaced longitudinal grooves.
IS : - Pressed into the cylindrical body to deform the pin stock outward.
EN: 28 740 Only straight Drilled hole required. No reaming needed.
ISO: 8740 Full Length Grooved Pins (with chamber end) are manufactured as per DIN: 1473, EN: 28 740, ISO: 8740

Socket Grooved Pin (Reverse Taper)

DIN: 1474 Grooved Pins are parallel pins with three equi-spaced longitudinal grooves.
IS : 7386 Pressed into the cylindrical body to deform the pin stock outward.
EN: 28 741 Only straight Drilled hole required. No reaming needed.
ISO: 8741 Socket Grooved Pins (Reverse Taper) are manufactured as per DIN: 1474, IS : 7386 , EN: 28 741, ISO: 8741

Locking Grooved Pin (Third Length Centre)

DIN: 1475 Grooved Pins are parallel pins with three equi-spaced longitudinal grooves.
IS : 7386 Pressed into the cylindrical body to deform the pin stock outward.
EN: 28 741 Only straight Drilled hole required. No reaming needed.
ISO: 8741 Locking Grooved Pins (Third Length Centre) are manufactured as per DIN: 1475, IS : 7386 , EN: 28 741, ISO: 8741

Locking Grooved Pin (Half Length Centre)

DIN: Grooved Pins are parallel pins with three equi-spaced longitudinal grooves.
IS : Pressed into the cylindrical body to deform the pin stock outward.
EN: 28 743 Only straight Drilled hole required. No reaming needed.
ISO: 8743 Locking Grooved Pins (Half Length Centre) are manufactured as per EN: 28 743, ISO: 8743

Groove Taper Pin (Full Length)

DIN: - 1471 Grooved Pins are parallel pins with three equi-spaced longitudinal grooves.
IS : 7368 Pressed into the cylindrical body to deform the pin stock outward.
EN: 28 744 Only straight Drilled hole required. No reaming needed.
ISO: 8744 Grooved Taper Pins (Full Length) are manufactured as per DIN: 1471, IS: 7368 , EN: 28 744, ISO: 8744

Half Length Grooved Taper Pin

DIN: - 1472 Grooved Pins are parallel pins with three equi-spaced longitudinal grooves.
IS : 7385 Pressed into the cylindrical body to deform the pin stock outward.
EN: 28 745 Only straight Drilled hole required. No reaming needed.
ISO: 8745 Grooved Taper Pins (Half Length) are manufactured as per DIN: 1472, IS: 7385 , EN: 28 745, ISO: 8745

Round Head Grooved Pin (Rivet)

DIN: - 1476 Grooved Pins are parallel pins with three equi-spaced longitudinal grooves.
IS : - Pressed into the cylindrical body to deform the pin stock outward.
EN: 28 746 Round Head Grooved Pins (Rivet)are manufactured as per DIN: 1476, EN: 28 746, ISO: 8746
ISO: 8746  

Countersunk Head Grooved Pin (Rivet)

DIN: - 1477 Grooved Pins are parallel pins with three equi-spaced longitudinal grooves.
IS : - Pressed into the cylindrical body to deform the pin stock outward.
EN: 28 747 Only straight Drilled hole required. No reaming needed.
ISO: 8747 Countersunk Head Grooved Pin (Rivet)are manufactured as per DIN: 1477, EN: 28 747, ISO: 8747

Grooved Pins with under-cut (Type A,B,C)

DIN: - 1469 Grooved Pins are parallel pins with three equi-spaced longitudinal grooves.
  Pressed into the cylindrical body to deform the pin stock outward.
  Only straight Drilled hole required. No reaming needed.
  Grooved Pins with under-cut (Type A,B,C)are manufactured as per DIN: 1469